Gizzard Harvester Rollers

roller-illustration

DeLong’s gizzard harvester rollers have a unique, patented design to perform specific removal of membranes and skin poultry gizzards with efficiency and precision. We manufacture these rollers to meet or exceed USDA approval codes, in a variety of lengths, constructed of stainless steel, and hardened stainless steel. Gizzard harvester rollers are available for all machines, old and new.

Note: Use the guide above and table below to ensure the proper measurements.

A: Peel Length

B: Peel Diameter (bushings)

C: Shaft Length (drive)

D: Shaft Diameter (bushing) (D)

OEM DeLong’s
Part Number
Peel
Length
(A)
Peel Diameter
(B)
Shaft Length
(Drive)
(C)
Shaft Diameter
(Bushing)
(D)
Drive Shafts
on Both Ends
Reverse Gear
on End of Peel
n/a 4016 16 in. 1.25 in. 3.25 in.  3/4 in.
Cantrell 3018 12 9/16 in. 1.125 in. 3.25 in.  16 mm.
Cantrell 4900 14 in. 1.25 in. 3.50 in.  3/4 in.
Cantrell
(Double Layer)
4910A & 4910B 14 in. 1.25 in. 3.25 in.  3/4 in.
Centennial 4017 10 1/8 in. 1.25 in. 3 in.  5/8 in.
Centennial 4019 14 in. 1.25 in. 3.25 in.  5/8 in.
DeLong 4200 24 in. 1.25 in. 5 in.  3/4 in.  
DeLong 4200 DS 24 in. 1.25 in. 5 in.  3/4 in.
DeLong 4200 SSR 24 in. 1.25 in. 5 in.  3/4 in.
DeLong 4200 DSSR 24 in. 1.25 in. 5 in.  3/4 in.
DeLong 4218 18 in. 1.25 in. 4 in.  3/4 in.
DeLong 4218 SSR 18 in. 1.25 in. 4 in.  3/4 in.  
Food Craft 4020 12 in. 1.25 in. 3 in.  .6875 in.
Lewis Machine 4740 14 in. 1.25 in. 3.25 in.  3/4 in.
Meyn 1013 12 5/8in. 1.025 in. 3.125 in.  16 mm.
Meyn (Double Layer) 1012A & 1012B 12.60 in. 1.025 in. 2.75 in.  16 mm.
Nord/Prime 990 11.625 in. 1.025 in. 3.95 in.  17 mm.
Marel/Stork 1505HY 11.60 in. 1.025 in. 3.125 in.  17 mm.
Marel/Stork 1509 9 15/16 in. 1.025 in. 3 in.  14 mm.
Marel/Stork 1510 9 15/16 in. 1.025 in. 3 in.  14 mm.
Marel/Stork 2010 11 5/8in. 1.0325 in. 3.125 in.  14 mm.
Marel/Stork 2500 11 5/8 in. 1.035 in. 3.25 in.  17 mm.
Marel/Stork 2500HY (High Yield) 11 5/8 in. 1.035 in. 3.25 in.  17 mm.
System Mate 4026 12 in. 1.25 in. 2.625 in.  5/8 in.
DeLong’s – AP2602 8700 24 in. 2 & 1-1/4 in. 4.50 in.  7/8 in..    
DeLong’s – AP2603 8800 24 in. 2 & 1-1/4 in. 4.50 in.  7/8 in.    

Bushings

DeLong’s recommends replacing your brass bushings every time you replace your poultry rollers. DeLong’s stocks all sizes for the end block application.

 

New brass bushings are always recommended when replacing any rollers. Bushings effect a rollers performance tremendously. Bad bushing can cause a good roller to perform poorly. DeLong’s stocks all sizes of bushings for any end block application.

bushings

Speak to a Poultry Expert About Your Equipment Needs